As one of the three supported form factors for FAIR Beam Instrumentation µTCA was chosen. The main advantages of µTCA systems are the high bandwidth for very high data rates and the full remote control features. The standard was enhanced by DESY and other high energy physics labs to the MTCA.4 specification for Physics. This form factor could get a successor for VME.

Envisaged are DAQ systems for fast sampling ADCS eg BPM systems, scaler systems for higher sampling rates and video imaging systems.

• ELMA MTCA.4 6-Slot (vertical)
• Schroff MTCA.4 6 Slot (vertical)
• Vadatech VT811 12-slot
• N.A.T. Native R2 6-Slot MTCA.4 2HE
• N.A.T. Native R9 12-Slot MTCA.4 9HE
• Powerbridge RackPak/M5-1 MTCA.4 2HE (this is the FAIR standard crate: info on configuration HERE!)

• Kontron AM5010
• ADlink AMC-1000
• NAT-PHYS-RTM Comex
• Concurrent AM902/412-32
• Concurrent AMG64/471-51

• div. NAT MCH (6 Slot, 12 Slot Phys)
• Vadatech UTC002

• SIS8300 10 Ch. ADC with RTM
• AM4301 4 Port NIC
• TAMC260 1 Slot PMC-Carrier for AMC
• Dual HPC FMC Carrier board MTCA.4 (open hardware)
• FMC ADC 250MHz 16 Bit (open hardware)
• FMC ADC 105MHz 14 BIt (open hardware)
• SIS8300KU 10.Ch. ADC with RTM
• SIS8800 32 Ch. Scaler
• SIS8980 16 Ch LE Discriminator RTM
• Vadatech AMC217 8-Ch Switch
• SIS8864 64bit I/O
• TAMC532 - 32Ch ADC 14 Bit with RTM
• FAIR Timing Receiver Node FTRN-AMC
• IOXOS IFC-1410 FMC Carrier & ADC-3117 FMC

The main standard MTCA-4 system consists of:

• Concurrent Technologies AM G64/471-51 CPU
• NAT-MCH-PHYS80
• NAT-PM-AC600D
• RackPak/M5-1 Chassis

Get M State via sensor: Example: Handle pulled out = M1 - board gets only management power

   $ ipmitool -I lan -H <mch_ip_addr> -A none sensor get "HS 009 AMC5"

Locating sensor record…
Sensor ID : HS 009 AMC5 (0x3c)
Entity ID : 193.101
Sensor Type (Discrete): PICMG FRU Hotswap
States Asserted : FRU Hot Swap
[Transition to M1]

Example 2: Handle pushed in (M4) - board is on

   $ ipmitool -I lan -H <mch_ip_addr> -A none sensor get "HS 009 AMC5"

Locating sensor record…
Sensor ID : HS 009 AMC5 (0x3c)
Entity ID : 193.101
Sensor Type (Discrete): PICMG FRU Hotswap
States Asserted : FRU Hot Swap
[Transition to M4]

Switch of dedicated FRU:

   $ ipmitool -I lan -H <mch_ip_addr> -A none picmg deactivate <fru_id>

Switch it on:

   $ ipmitool -I lan -H <mch_ip_addr> -A none picmg activate <fru_id>

Cold reboot of complete system:

   $ ipmitool -I lan -H <mch_ip_addr> -A none chassis power reset

Warm-reboot:

   $ ipmitool -I lan -H <mch_ip_addr> -A none chassis power cycle