Differences

This shows you the differences between two versions of the page.

--- projects:maps:mapsadapter:analogsignalmodul:overview [2020/07/03 21:07]
carsten [2.) Boards]
+++ projects:maps:mapsadapter:analogsignalmodul:overview [2020/07/05 11:53] (current)
carsten [3.) Internal pictures]
@@ Line 17: / Line 17: @@
 The following picture illustrates the flow of meassurement gate "Messfenster" from the input at one of the Lemo connectors at the front placed about the huge connector (alternativ on back side under analog BNC-inputs): Current default input is the most left module from front side. This signal can be directed on the "**68AMP_9Lemo-board**" via jumper to one of ten (PFI0-PFI9). Deault is PFI0. PFI-Lines to the connected NI-ADC PXI-6133. These are **P**rogrammable **F**unktion **I**nputs . They can be determed to be an input our an output. This will be done in the setup of the ADC-board. Inside the PXI-crate this signal is then distributed to all other ADC-bords. It might be possible to get it out again at 68AMP_9Lemo-board if the related board on the other ADCs ist determed to be an output then.
-{{:projects:maps:mapsadapter:analogsignalmodul:messfenster_signalverlauf.jpg?direct&600 |Messfenster Signalverlauf}}
+{{ :projects:maps:mapsadapter:analogsignalmodul:messfenster_signalverlauf.jpg?direct&600 |Messfenster Signalverlauf}}
+===== 2.) Boards =====
-\\
-===== 2.) Boards ======
 This module does only house board [[projects:maps:mapsadapter:analogsignalmodul:68amp_9lemo|Board "68AMP_9Lemo"]].
 ===== 3.) Internal pictures =====
+Grey comments are possible adptions to MAPS2020!
 ^  Front  ^  Back  ^ ^
-|  {{ :projects:maps:mapsadapter:analogsignalmodul:s7302067.jpg?nolink&300 |}}  |  {{ :projects:maps:mapsadapter:analogsignalmodul:s7302068.jpg?nolink&300 |}}  | Front and back of one of four submodules:\\ \\ __Front: 4x board with each:__\\ 1x Front 68pol connector to NI-ADC (8 channel) ⇒ 2x RJ45 (4 channel)\\ 1x LEMO 00 monitor output\\ \\ __Back:__\\ 1x LEMO 00 Timing input\\ 8x LEMO 00 diff. analog input per trafo (internal)  |
+|  {{ :projects:maps:mapsadapter:analogsignalmodul:s7302067.jpg?nolink&300 |}}  |  {{ :projects:maps:mapsadapter:analogsignalmodul:s7302068.jpg?nolink&300 |}}  | Front and back of one of four submodules:\\ \\ __Front: 4x board with each:__\\ 1x Front 68pol connector to NI-ADC (8 channel)\\ <color grey>⇒ 2x RJ45 (4 channel) = Σ 8x RJ45</color>\\ 1x LEMO 00 monitor output\\ <color grey>⇒ 4x trigger @ X2 connector</color>\\ \\ __Back:__\\ 1x LEMO 00 Timing input\\ 8x LEMO 00 diff. analog input per trafo (internal)  |
 |  {{ :projects:maps:mapsadapter:analogsignalmodul:s7302069.jpg?direct&600 |}}  || View inside analog modul  |
 |  {{ :projects:maps:mapsadapter:analogsignalmodul:s7302070.jpg?nolink&600 |}}  || modules internal back side  |

GSI - BEA Wiki

User Tools

Site Tools

Differences

Page Tools