Differences

This shows you the differences between two versions of the page.

--- projects:maps:mapsadapter:overview [2011/12/16 15:51]
carsten [Related topics]
+++ projects:maps:mapsadapter:overview [2020/07/05 12:03] (current)
carsten [Related topics]
@@ Line 1: / Line 1: @@
-====== MAPS-adapter ======
+☚ [[projects:maps:overview| Zurück]] ★
-The adapter in it's hole consists of one 6 unit device collecting 128 AC-trafo signals on BNC connectors at the back and one 3 unit high "Rahmenpulsmodul" collecting 128 "Rahmenpulse" on it's back.
+====== MAPS Adapter ======
+The adapter consists of one 6U crate which collects 128 BCT signals through BNC connectors at the rear panel, and one 3U "Rahmenpuls-Modul" collecting 128 gate pulses on it's rear panel.
 ===== Related topics =====
-The adpter is a completely passive adapter and exists internally as shown below out of several boards as are:
+The adapter is a completely passive device, and is internally composed of several boards as shown below:
-^  Hardware  ^  Signal and Info  ^
+^  Hardware  ^  Signals and Info  ^
-|  Internals 6 unit "[[projects:maps:mapsadapter:analogsignalmodul:overview|Analog signal modul]]"  ||
+|  Internal 6U "[[projects:maps:mapsadapter:analogsignalmodul:overview|Analogue signal module]]"  ||
-| [[projects:maps:mapsadapter:analogsignalmodul:68amp_9lemo|68AMP_9LEMO]]\\  Those 2x8 boards bundles analog signals and measurement gate to NI-cable | Flow of [[projects:maps:mapsadapter:analogsignalmodul:overview|"Messfenstersignal"]] and possible Choises there:\\   |
+| **"[[projects:maps:mapsadapter:analogsignalmodul:68amp_9lemo|68AMP_9LEMO]]"**\\  These 2x8 boards bundle analogue signals and measurement gate pulses into NI-cable | Flow of [[projects:maps:mapsadapter:analogsignalmodul:overview|"Messfenstersignal"]] and possible Choises there:\\   |
-|  Internals 3 unit "[[projects:maps:mapsadapter:rahmenpulsmodul:overview|Rahmenpulsmodul]]"  ||
+|  Internal 3U "[[projects:maps:mapsadapter:rahmenpulsmodul:overview|Rahmenpulsmodul]]"  ||
-| [[projects:maps:mapsadapter:rahmenpulsmodul:rahmenplsback|Backplane "Rahmenpulsback"]] \\ That board collects "Rahmenpulse" from back and passes it internaly to the four ... | Flow of signals from and to PXI-7811 FPGA board:\\ MAPS-Bus-signals / "Rahmenpulse" |
+| **"[[projects:maps:mapsadapter:rahmenpulsmodul:rahmenplsback|Backplane "Rahmenpulsback"]]"** \\ This board collects "Rahmenpulse" from rear side and passes them internaly to the four ... | [[projects:maps:mapsadapter:rahmenpulsmodul:overview|Signals to PXI-7811R FPGA board]]:\\ MAPS-Bus-signals / Rahmenpulse |
-| [[projects:maps:mapsadapter:rahmenpulsmodul:amp68vg96|AMP68VG96]] \\ This four boards adaps the "Rahmenpulse" from the backplane via VG connector to NI-VHDCI cables connecte to the NI7811 FPGA-board.  |  |
+| **"[[projects:maps:mapsadapter:rahmenpulsmodul:amp68vg96|AMP68VG96]]"** \\ These four boards adapt the "Rahmenpulse" from the backplane via VG connectors to NI-VHDCI cables connected to the NI7811 FPGA-board.  |  |
-===== MAPS-Adpter front =====
+===== MAPS-Adapter Front View =====
-Empty seperate slots are ment for storing away rigid Ni-cables that are available only in certain length. That should provide more acurateness appart from the great number of this cables. Hole adapter interfaces between the digitizer signals analog signal and "Rahmenpuls" and the NI-crate:  \\
+Empty seperated slots provide storage space for the quite rigid NI multiline cables, which are available only in fixed lengths. That should provide more acurateness appart from the great number of this cables. Hole adapter interfaces between the digitizer signals analog signal and "Rahmenpuls" and the NI-crate:  \\
 {{ :projects:maps:front_maps-adapter.jpg?nolink&800 |MAPS-Adapter front}}
-===== MAPS-Adapter back =====
+===== MAPS-Adapter Rear View =====
 {{ :projects:maps:rueckseiten.jpg?nolink&800 |MAPS-Adapter back}}
+☚ [[projects:maps:overview| Zurück]] ★

GSI - BEA Wiki

User Tools

Site Tools

Differences

Page Tools