Differences

This shows you the differences between two versions of the page.

--- instrument_hardware [2018/12/06 14:09]
vschaefer
+++ instrument_hardware [2020/01/16 09:46] (current)
cpiromalli
@@ Line 1: / Line 1: @@
 ====== Instrument Hardware ======
-===== Detector Hardware =====
+[[Technical Concept|Technical Concept]]
-The scintillating screen is inserted into the beam under an angle of 45°. Through a viewport, located at 90° with respect to the beam, a camera observes the screen.
+{{ :cupid_schema.jpg?nolink |}}
-{{:drawing_of_the_scintillating_screen_setup_on_a_flange.jpg?nolink&400|}}
+**[[Detector Hardware|Detector Hardware]]**
-<color #7092be>The drawing of the scintillating screen setup on a flange with a target under 45° in respect to the beam. </color>
+**[[Optical Setup|Optical Setup]]**
+**[[Additional Parts/Assembly|Additional Parts/Assembly]]**
-The mechanical constituents of one Scintillating Screen Setup are the following parts:
+**[[Components at the beam line|Components at the beam line]]**
-  * 	Detector consisting of scintillating screen and target holder.
+**[[Data Acquisition Hardware|Data Acquisition Hardware]]**
-  *     Pneumatic driven linear actuator.
-  * 	Diagnostic chamber for installation of linear actuators.
-  * 	Additional parts for detector installation on linear actuator.
-==== Pneumatic Driven Linear Actuator ====
+**[[Data Acquisition Software|Data Acquisition Software]]**
-The linear actuator moves the detector (scintillating screen and holder) into the beam center and out of the beam. The four different detectors are foreseen correspond to four different linear actuators.
+**[[Supported Infrastructure (HV, Pressurized Air, Detector Gas)|Supported Infrastructure (HV, Pressurized Air, Detector Gas)]]**
-^ Detector    ^ Distance Flange-Beam Center [mm] ^ Stroke [mm] ^ Bakeout ^ BD-type number ^ Drawing number   ^
-| FT-DF 2010  | 270                              | 150         | No      | FT-DL 2210     | BD-1018821-A-000 |
-| FT-DF 2011  | 270                              | 150         | Yes     | FT-DL 2220     | BD-1018881-A-000 |
-| FT-DF 2020  | 370                              | 200         | No      | FT-DL 2230     | BD-1014852-A-000 |
-| FT-DF 2021  | 370                              | 200         | Yes     | FT-DL 2240     | BD-1018450-A-000 |
-{{:technical_drawing_of_linear_actuator.jpg?nolink&600|}}
-<color #7092be>Technical drawing of linear actuator with camera setup.</color>
-===== Optical Setup =====
-The optical constituents of one Scintillating Screen are the following parts:
-==== Screen material ====
-The detector consists of the scintillating screen (target) and the target holder. The scintillating screen is a round disk of scintillating material (solid or coated material), fixed in a holder with permanent alignment marks outside the active area.
-{{:technical_drawing_left.jpg?nolink&200|}} {{::technical_drawing_right.jpg?nolink&200|}}
-<color #7092be>The technical drawing (left) and photo (right) of the scintillating screen on target holder.</color>
-^ SCR Material       ^ Type                   ^ Application                 ^
-| Al2O3:Cr (Chromox) | Solid target material  | Standard light applications |
-| Gd2O2S:Tb (P43)    | Coated on a plate      | Low light applications      |
-| YAG:Ce             | Solid target material  | Low light applications      |
-In the HEBT lines, two different detector sizes are used with an active area of Ø 100 mm and Ø 120 mm, mainly Chromox.
-^ Detector size (active area) ^ Bake-out ^BD-type number ^ Drawing number   ^
-| D100                        | No       | FT-DF 2010    | BD-1018552-A-000 |

GSI - BEA Wiki

User Tools

Site Tools

Differences

Page Tools