projects:ablass:dtim-hardware
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
projects:ablass:dtim-hardware [2014/11/13 14:56] pmiedzik [Version 2] |
projects:ablass:dtim-hardware [2014/11/13 16:28] (current) pmiedzik [DTim Version 2] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== DTim ====== | + | ===== DTim Version 1 ===== |
| - | + | ||
| - | + | ||
| - | ==== Version 1 ==== | + | |
| Maintained by Dmitry Lyakin < | Maintained by Dmitry Lyakin < | ||
| Line 9: | Line 6: | ||
| - | ==== Version 2 ==== | + | ===== DTim Version 2 ===== |
| **Warning!!! Firmware Version 2 is not compatible with Version 1. | **Warning!!! Firmware Version 2 is not compatible with Version 1. | ||
| Before you will upgrade firmware to latest version please read carefully whole instruction.** | Before you will upgrade firmware to latest version please read carefully whole instruction.** | ||
| Line 16: | Line 13: | ||
| Components: | Components: | ||
| + | * CES RIO3 8064 (LynxOS 3.1.0a) | ||
| * DTim | * DTim | ||
| - | | + | |
| - | * RIO: LynxOS | + | |
| - | * Ablas server (RIO) | + | * DTim Hardware: |
| - | * Scaler module | + | * Board version: FIXME |
| + | * FPGA firmware: V2.0@2014-10-01 | ||
| + | * DSP firmware: not used | ||
| + | * Front Panel firmware: FIXME | ||
| + | * Software: | ||
| + | * RIO Server: FIXME | ||
| + | * ABLASS Provider: FIXME | ||
| + | * ABLASS GUI: FIXME | ||
| + | * ABLASS ... | ||
| - | === Lemo Input/ | + | |
| + | |||
| + | ==== Lemo Input/ | ||
| + | FIXME Add front panel picture | ||
| ^ Index ^ Jumper setting ^ Function ^ | ^ Index ^ Jumper setting ^ Function ^ | ||
| Line 34: | Line 43: | ||
| ^ 8 | Input | Not used | | ^ 8 | Input | Not used | | ||
| - | === Header 1 === | + | ==== Header 1 ==== |
| Not used | Not used | ||
| Line 48: | Line 57: | ||
| ^ 8 | High impedance | Not used | | ^ 8 | High impedance | Not used | | ||
| - | === Header 2 === | + | ==== Header 2 ==== |
| Header 2 is used to emulate VME Geographical Address. | Header 2 is used to emulate VME Geographical Address. | ||
| Line 64: | Line 73: | ||
| ^ 8 | High impedance | Not used | No | | ^ 8 | High impedance | Not used | No | | ||
| - | === Header 3 === | + | ==== Header 3 ==== |
| Header 3 is used for debugging purposes. | Header 3 is used for debugging purposes. | ||
| Line 81: | Line 90: | ||
| GIT (Read Only): **%%git:// | GIT (Read Only): **%%git:// | ||
| GIT (Read/ | GIT (Read/ | ||
| - | |||
| - | |||
| Wishbone Slaves: | Wishbone Slaves: | ||
| * [[projects: | * [[projects: | ||
| * [[projects: | * [[projects: | ||
| + | |||
| + | ==== Diagnostic Tools ==== | ||
| + | **WARNING!!! Diagnostic tools are available only for Linux Operating system** | ||
| + | |||
| + | === dtim_config === | ||
| + | === dtim_readout === | ||
| + | === dtim_sim === | ||
| + | === dtim_raw === | ||
| + | |||
| + | ===== ABLASS Server ===== | ||
| + | |||
| + | === Configuration === | ||
| + | === Startup === | ||
| + | ablax_ablass process will demonize itself (http:// | ||
| + | There are some important options that can be passed to | ||
| + | * **-d level** debug mask. Default 0 | ||
| + | * **-f** do not demonize, stay in background. | ||
| + | * **-p pid_file** store pid into pid_file file. Default: ./ | ||
| + | * **-c config_file** path co configuration file. Default: ./ | ||
| + | * **-l log_file** path to log file. Default: **./ | ||
| + | |||
| + | === Debug mask === | ||
| + | 0 - no debug/log features\\ | ||
| + | 1 - debug general\\ | ||
| + | 2 - debug cycle'' | ||
| + | 3 - ... \\ | ||
| + | |||
projects/ablass/dtim-hardware.1415886979.txt.gz · Last modified: 2014/11/13 14:56 by pmiedzik
Page Tools
