This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
ds:hardware:mtca:overview [2021/02/10 08:33] tobiashoffmann |
ds:hardware:mtca:overview [2024/09/04 15:18] (current) tobiashoffmann [µTCA Crates] |
||
---|---|---|---|
Line 5: | Line 5: | ||
Envisaged are DAQ systems for fast sampling ADCS eg BPM systems, scaler systems for higher sampling rates and video imaging systems. | Envisaged are DAQ systems for fast sampling ADCS eg BPM systems, scaler systems for higher sampling rates and video imaging systems. | ||
- | So far BI has tested following µTCA parts: | ||
- | |||
- | ===== µTCA IPMI Control ===== | ||
- | |||
- | Get M State via sensor: | ||
- | Example: Handle pulled out = M1 - board gets only management power | ||
- | $ ipmitool -I lan -H < | ||
- | Locating sensor record...\\ | ||
- | Sensor ID : HS 009 AMC5 (0x3c)\\ | ||
- | Entity ID : 193.101\\ | ||
- | Sensor Type (Discrete): PICMG FRU Hotswap\\ | ||
- | States Asserted | ||
- | [Transition to M1]\\ | ||
- | |||
- | Example 2: Handle pushed in (M4) - board is on | ||
- | |||
- | $ ipmitool -I lan -H < | ||
- | Locating sensor record...\\ | ||
- | Sensor ID : HS 009 AMC5 (0x3c)\\ | ||
- | | ||
- | | ||
- | | ||
- | [Transition to M4]\\ | ||
- | |||
- | Switch of dedicated FRU: | ||
- | $ ipmitool -I lan -H < | ||
- | |||
- | Switch it on: | ||
- | $ ipmitool -I lan -H < | ||
- | |||
- | Cold reboot of complete system: | ||
- | $ ipmitool -I lan -H < | ||
- | |||
- | Warm-reboot: | ||
- | $ ipmitool -I lan -H < | ||
Line 49: | Line 14: | ||
* N.A.T. Native R2 6-Slot MTCA.4 2HE | * N.A.T. Native R2 6-Slot MTCA.4 2HE | ||
* N.A.T. Native R9 12-Slot MTCA.4 9HE | * N.A.T. Native R9 12-Slot MTCA.4 9HE | ||
- | * Powerbridge RackPak/ | + | * Powerbridge RackPak/ |
Line 78: | Line 43: | ||
* SIS8800 32 Ch. Scaler | * SIS8800 32 Ch. Scaler | ||
* SIS8980 16 Ch LE Discriminator RTM | * SIS8980 16 Ch LE Discriminator RTM | ||
- | * Vadatech AMC217 8-Ch Switch | + | * [[ds: |
* [[: | * [[: | ||
* TAMC532 - 32Ch ADC 14 Bit with RTM | * TAMC532 - 32Ch ADC 14 Bit with RTM | ||
Line 91: | Line 56: | ||
* NAT-PM-AC600D | * NAT-PM-AC600D | ||
* RackPak/ | * RackPak/ | ||
+ | |||
+ | |||
+ | ===== µTCA IPMI Control ===== | ||
+ | |||
+ | Get M State via sensor: | ||
+ | Example: Handle pulled out = M1 - board gets only management power | ||
+ | $ ipmitool -I lan -H < | ||
+ | Locating sensor record...\\ | ||
+ | Sensor ID : HS 009 AMC5 (0x3c)\\ | ||
+ | Entity ID : 193.101\\ | ||
+ | Sensor Type (Discrete): PICMG FRU Hotswap\\ | ||
+ | States Asserted | ||
+ | [Transition to M1]\\ | ||
+ | |||
+ | Example 2: Handle pushed in (M4) - board is on | ||
+ | |||
+ | $ ipmitool -I lan -H < | ||
+ | Locating sensor record...\\ | ||
+ | Sensor ID : HS 009 AMC5 (0x3c)\\ | ||
+ | | ||
+ | | ||
+ | | ||
+ | [Transition to M4]\\ | ||
+ | |||
+ | Switch of dedicated FRU: | ||
+ | $ ipmitool -I lan -H < | ||
+ | |||
+ | Switch it on: | ||
+ | $ ipmitool -I lan -H < | ||
+ | |||
+ | Cold reboot of complete system: | ||
+ | $ ipmitool -I lan -H < | ||
+ | |||
+ | Warm-reboot: | ||
+ | $ ipmitool -I lan -H < | ||