This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
hi:hi:blmservicerecords [2019/09/19 15:04] p.boutachkov BLM Service Records |
hi:hi:blmservicerecords [2020/12/11 13:33] p.boutachkov FAIR BLM records |
||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Calibration ====== | ||
+ | The BLM calibration is performed with a < | ||
+ | The source emits a single gamma at 661.7 keV. The source activity was 323.2 kBq as of 11.01.2019. Its serial number is AB-9020, 370 kBq when purchased. | ||
+ | |||
+ | I have used 10 s integration time and set all BLM to count 30 k. (3 kHz) | ||
+ | |||
+ | Note on the light yield. Reference Glenn Knoll 3rd edition p.235 and p226 NE102A 10 k photons per MeV. BC400 light output 0.65 of NE102A (anthrscene). Hence one can expect: 6500 photons / keV | ||
+ | |||
+ | Bellow is a spectrum taken with the HDO6104A scope when for a BLM set to count 3 kHz (in this case XP2972 34391) | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ====== XP2972 PMT History ====== | ||
+ | CBS - Cathode Blue sensitivity | ||
+ | ABS - For a anode blue sensitivity | ||
+ | Id - Dark current | ||
+ | |||
+ | ^ SN ^ CBS [uA/lmF] ^ ABS [A/lmF] ^ HV [V] ^ Id[nA] ^ Gain [10< | ||
+ | | 34391 | 12.6 | 10 | 1188 | 4.98 | 0.79 | new, will be installed in TE1 | | ||
+ | | 29181 | | | | | | used, low gain, was in S07DL1R | | ||
+ | |||
====== GS06DL3U ====== | ====== GS06DL3U ====== | ||
Reason for the service: The detector counts more than 10 times compare to the detectors above, left and right of it. | Reason for the service: The detector counts more than 10 times compare to the detectors above, left and right of it. | ||
Line 11: | Line 32: | ||
- Dark counts, trigger 30 mV : | - Dark counts, trigger 30 mV : | ||
- | ^ HV [V] ^ I_leakage | + | ^ HV [V] ^ I< |
| 300 | 200 | 0 | | | 300 | 200 | 0 | | ||
| 1000 | 672 | 0 | | | 1000 | 672 | 0 | | ||
| 1500 | 1008 | 30 | | | 1500 | 1008 | 30 | | ||
- | * Visual inspection of the SCI | + | |
* No yellowing, signs of mechanical damage on the surface. | * No yellowing, signs of mechanical damage on the surface. | ||
* Under UV, no spots | * Under UV, no spots | ||
+ | The Standard operating voltage is 1100 V, I< | ||
+ | |||
+ | |||
+ | ====== FAIR Type ====== | ||
+ | * Measurement with Micsing scope, BW 150 MHz, dT=100 ns/div, dV = 200 mV/div, trigger -104 mV | ||
+ | * The LED drive, pulse, positive, voltage is 3V, width 50 ns, rise/fall time 5 ns, frequency 1 kHz | ||
+ | |||
+ | ^ PMT S/N ^ AVD S/N [uA] ^ I@1500V [uA] ^ Dark counts@1500V [Hz]^ Vmin[V] LED on ^ | ||
+ | | LA8177 | ||
+ | | LA8178 | ||
+ | | LA8179 | ||