<anno:num>text</anno><@anno:num>annotation</@anno> lalala <anno:num>text</anno><@anno:[num;;class_name]>annotation</@anno> ok oooo

This document describes the setup and initial commissioning of the 90 Supermicro X11SPL-F (FAIR) IPCs procured from RaidMediaSystems in 2021.

Following tools are required for full configuration and commissioning of the IPC systems.

• Linux PC with LAN access to ACC network, resp. BEA-DAT hardware database
• VGA cable to monitor
• Two power cables
• Keyboard acces to CPU
• Two LAN patch cables (IPMI and CPU)
• Access to BEA-DAT Barcode Printers (small and large labels)
• Web browser

For the Moment there is sdlx040 prepared for this type of work.

RaidMediaSystems is able to provide hardware data for each individual system before or at delivery time.
Besides all serial numbers, the MAC addresses of CPU and IPMI are provided.
As a first step, it is recommended to request valid IP addresses and network names for the new products.
A mail has to be sent to ACO (Pfister, Vincelli) with the MAC addresses (LAN1 for CPU),
a proposed network name and a valid boot server or a valid exemplary FEC name to be copied from.

Example DHCP parameter: server=“fsl00c” filename=“/lobi/pxe/pxelinux.0”
The network names for CPUs (FEC) are always: sddscXXX
The network names for IPMI (FEC) are always: sddscXXXrm

Remark: dsc means “device stub controller”, rm means “remote”
NB: for the IPC procurement FAIR from 2021 all IPCs are already registered and provided with IP for LAN and IPMI.

After delivery, carefully check the packaging and in case of damage, file a complaint, if necessary.
The usual scope of delivery for a system is the IPC preconfigured for PXE boot (without harddrive) and power cables.

As soon as the IP addresses of IPMI and CPU are available, the systems should be registered in the BEA-DAT hardware database by assigning a CID and a barcode.
The database is located here: http://sdlx046.acc.gsi.de:8080/bihw/login
To access the database you need an account (→ H. Bräuning).
First a DB entry of an existing crate is opened and copied.
The name and network name must be adapted and the MAC address, serial number and order number need to be filled.
It is helpful to enter a purpose or the sponsor for the system in the note field.
A large barcode (sdaprn001.acc.gsi.de or sdaprn003.acc.gsi.de)
with FEC name and IP, Fig. 1, shall be printed and sticked onto the front panel as shown in Fig. 2.

Figure 1: Barcode on IPC Chassis with IP and FEC Name

Figure 2: Barcode and inventory label on IPC frontside

Figure 3: IPC backside with labelled LAN/IPMI ports

Small labels based on 6mm tape and named LAN1, LAN2 and IPMI are to be attached to the LAN and IPMI ports, as shown in the picture, on the back of the IPC.

The BIOS can be accessed with DEL. Check the Time and Date.
The 90 FAIR IPCs from the 2021 order are preconfigured with PXE network boot.
No further settings are required.

The FAIR IPCs can be fully remote controlled via the IPMI LAN port on the backside.
The IPMI network name follows the concept: sddscXXXrm.acc.gsi.de
where “rm” means “remote”.
Enter this network name in the location bar in your browser and login with
ADMIN / RMS.ChangeMe
After successful login change the ADMIN password to
!T01…
and add a root user with
n0k…… -password.

To boot via PXE the IPC must be correctly set-up on the tftp-boot server.
The default tftp-boot server is organized via login on asl740
or after update to Rocky 8 on asl751.
This requires an ACC network account.
Without this preparation, the CPU will not boot from the network.
Execute the following steps:
ssh username@asl740.acc.gsi.de (or asl751) cd /common/tftp/lobi/pxe/pxelinux.cfg

Use the script: ./createPxeLink.sh <fec-name> <config-file>
e.g. ./createPxeLink.sh sddsc194 R8_R0_85_IPC

or manually:
gethostip <fec-name> e.g. sddsc010
Output of gethostip looks like this:
sddsc010.acc.gsi.de 140.181.132.240 8CB584F0
Create a symbolic link from BootOS-Config File
e.g. C7_R14_79_UTCA.enp15s0 to fec-name
ln -s C7_R14_79_UTCA_NET10.enp15s0 sddsc010
Create a symbolic link from fec-name to the HEX IP Code
ln -s sddsc010 8CB584F0

Finally boot the IPC and try a login as root / new….